-
$598.00 Off
$29,262.99 List Price:
$29,860.99Made in USA 5,000 PSI Overview The Digga SD45HPS is a high-powered single-speed drive built for drilling work, and the figure that defines it is pressure: the high-powered Supa drives run at up to 5,000 PSI where the standard range stops at 3,500. This... -
$776.00 Off
$37,994.99 List Price:
$38,770.99Made in USA ECV fitted Overview This screw anchor drive is the Digga SD45, part of the Supa range built specifically for helical pile and screw anchor installation rather than adapted from a drilling drive. It is the entry point to the Supa range... -
$38.00 Off
$1,822.99 List Price:
$1,860.99Made in USA 12-mo warranty Overview The RYNO is a piling auger mount built around a bolted base plate rather than a welded one, and that choice is deliberate: a bolted plate can be replaced when it wears or when the machine changes, without... -
$37.00 Off
$1,803.99 List Price:
$1,840.99Made in USA Teeth & pilot included Overview The Digga RC8 is an excavator auger bit for combination rock and earth drilling, supplied here on a 3" hex hub for the larger excavator drives. It runs the same B7 taper-tooth head as the RC6... -
$56.00 Off
$2,714.99 List Price:
$2,770.99Made in USA Teeth & pilot included Overview This heavy-duty rock auger bit is the Digga RC11, and the difference from the RC10 is the head: a larger B8 casting that takes TTL-3 extra heavy duty tungsten teeth rather than the TTD-3 the RC10... -
$48.00 Off
$2,332.99 List Price:
$2,380.99Made in USA Teeth & pilot included Overview The Digga RC10 is an excavator auger bit on a 100mm square hub, which puts it in a different class from the hex-shaft bits below it. The square drive is what transmits torque at this level... -
$12.00 Off
$588.99 List Price:
$600.99Made in USA 12-mo warranty Overview This skid steer electrical kit is for machines with no service plug at all — which describes a great many older loaders and plenty of current ones. Rather than converting a plug you do not have, it brings... -
$9.00 Off
$436.99 List Price:
$445.99Made in USA 12-mo warranty Overview This 2 speed auger drive controller kit is what actually lets you use the second speed. Digga ships every two-speed drive with a 10ft powerlead and a two-pin connector, but the controller is a separate item — so... -
$192.00 Off
$9,408.99 List Price:
$9,600.99Made in USA 12-mo warranty Overview This Digga skid steer broom attachment is a manual-pivot angle broom built for industrial, municipal and construction sweeping, available in 72", 84" and 96" widths with manual 30 ° right and left angling. Three choices shape your order:... -
$97.00 Off
$4,743.99 List Price:
$4,840.99Made in USA 12-mo warranty Overview This 2-way flow valve mounts to the motor inside the bail of the auger drive itself, rather than being bolted somewhere on your machine. That is the distinction from Digga’s external kits, and it carries one hard condition:... -
$5.00 Off
$215.99 List Price:
$220.99Made in USA 12-mo warranty Overview This electrical kit connects a Digga hydraulic-pivot attachment to a skid steer that already has a service plug, converting the machine’s existing plug to the two-pin connector the attachment uses. Two versions cover the two common plug standards:... -
$233.00 Off
$11,397.99 List Price:
$11,630.99Made in USA 12-mo warranty Overview This skid steer broom attachment angles hydraulically from the cab rather than by hand at the attachment, and on a job where the angle changes often that is the entire argument for it. The manual version means climbing... -
$54.00 Off
$2,606.99 List Price:
$2,660.99Made in USA 12-mo warranty Overview This external 2 way flow valve kit adds forward and reverse auger rotation to a machine that only has a single-acting hammer circuit, and unlike Digga’s integrated valve it mounts to your machine rather than inside the drive.... -
$31.00 Off
$1,499.99 List Price:
$1,530.99Made in USA 12-mo warranty Overview This external 2 way flow valve kit adds forward and reverse auger rotation to a machine that only has a single-acting hammer circuit, and unlike Digga’s integrated valve it mounts to your machine rather than inside the drive.... -
$5.00 Off
$225.99 List Price:
$230.99Made in USA 12-mo warranty Overview This 2 way flow valve extension harness runs between a Digga external valve and the switch in your cab, sold separately in 10ft, 20ft, 40ft and 50ft lengths. It is the part people order second — usually after... -
$58.00 Off
$2,822.99 List Price:
$2,880.99Made in USA 12-mo warranty Overview This excavator extension boom puts the auger drive further from the machine, which is what lets you drill or pile in places the dipper alone cannot reach — over a bank, past an obstruction, or down into ground... -
$80.00 Off
$3,880.99 List Price:
$3,960.99Made in USA Teeth & pilot included Overview This dedicated rock auger bit is the Digga DR11, the largest in the range, on a 100mm square hub for 18–30 tonne excavators and the SD Supa drives. Like the DR6 it uses rotating carbide bullet... -
$188.00 Off
$9,182.99 List Price:
$9,370.99Made in USA Crumber bar included Overview This high-flow skid steer trencher attachment is the Digga Bigfoot XD, and the numbers separate it clearly from the standard Bigfoot: a 6K Bell Eaton motor delivering 67 hp continuous against 34, on 28–45 GPM, digging to... -
$12.00 Off
$558.99 List Price:
$570.99Made in USA 12-mo warranty Overview This backhoe auger mount kit is the cradle that carries a Digga auger drive on a backhoe dipper, supplied with the linkage and pin. Two sizes cover drives 5 through 7 and drives 9, 12, 13 and 16.... -
$15.00 Off
$690.99 List Price:
$705.99Made in USA 12-mo warranty Overview This excavator auger mount is a wedge lock hitch for the Hitachi ZX26, letting a Digga auger drive pin straight into the machine’s factory coupler rather than needing a separate pin-on bracket. Digga catalogues it under the John...
SHOP DIGGA ATTACHEMENTS BY TYPE
HOW TO CHOOSE THE RIGHT DIGGA ATTACHMENTS
Match the Drive Unit to Your Machine
Digga auger drives come in different torque classes. If you're running a skid steer, a mid-range digga auger drive like the PDX2 might be perfect. Excavators often need more torque.
Consider the Ground Conditions
Not all dirt is equal. Loose soil? Standard bits will do. Clay or rock? You’ll want digga auger bits with bolt-on teeth for better bite and longer life on hard ground.
Look for Smart Features
Want faster, straighter holes? The digga halo system uses LED indicators to guide you as you drill. It's all about keeping your flight path true and consistent.
Don’t Forget Mounts & Hoses
We offer full kits with everything included hoses, mounts, even cradles. Tell us your hydraulic specs and we’ll match your setup with the right digga attachments.
WHY BUY DIGGA ATTACHMENTS FROM ESKIDSTEER.COM
Official Digga Partner
We’re a trusted source for authentic digga attachments, straight from the manufacturer. Every item is backed by full factory support and covered under warranty.
Expert Advice, No Guesswork
Our team knows these tools inside and out. Whether you're choosing a digga trencher or auger, we can walk you through torque specs, machine fit, and ground condition needs.
Complete Kits, Ready to Work
You won’t be chasing parts. Each setup includes the drive, hoses, mounts, and bits. Just bolt it on and get to work with a full digga augers system, pre-matched to your machine.
Transparent Pricing & Financing
What you see is what you pay. We also offer flexible financing so you can get the gear you need now without draining your budget.
Fast, Tracked Shipping
Your job can’t wait, and neither do we. Orders ship quickly with full tracking, so you always know where your digga attachments are and when they’ll arrive.
NEED HELP CHOOSING THE RIGHT DIGGA ATTACHMENT?
From torque specs to soil type, we’ve got you covered. Whether you're drilling, trenching, or mounting a drive head, our team can help you pick the right setup for your machine.
Contact Us →
FAQs
What size auger drive do I need for my skid steer?
It depends on your hydraulic flow and job type. For general dirt drilling, most standard-flow machines pair well with Digga’s PD series.
Are Digga augers compatible with other brands like Bobcat or CAT?
Yes. Digga attachments include universal mounts and hose options. We’ll help match the drive and bit setup to your machine’s specs.
How do I maintain a Digga auger drive?
Keep it greased, inspect bits, and store it dry. Digga auger drives are low-maintenance, but a quick check now and then saves downtime later.
What kind of teeth do I need for rocky ground?
Use bolt-on rock teeth or pilot points with wear protection. Let us know your soil type and we’ll guide you to the right digga auger bits.
Are Digga attachments covered by warranty?
Yes. All digga attachments we sell come with manufacturer-backed warranties. Coverage varies by model—ask us for details.`
CUSTOMER SUPPORT
If you need support, we’re here to help.
Mon-Fri: 8am-4:30pm CT
Sat-Sun: Closed
You can also email us for customer service or product support.
support@eskidsteer.com
Call or Text
To place a new order or for assistance with an existing order call or text us at
+1 (866) 757-8337
Live Chat
Have questions or need help?
Chat with us using the icon in the bottom left.
Start new chat
- Choosing a selection results in a full page refresh.